Bill Bune Enterprises-Anoka Minnesota-motorcycle, snowmobile, atv & watercraft

(763)427-6738

(763)576-9924

(800) 642-2913

Please email us for any inquiries:

bbune@goldengate.net

BORING

(Includes port champers & hone to finish size)

2-CYCLE

4-CYCLE

EACH CYLINDER (w/ customer piston)

each

60.00

EACH CYLINDER

each

50.00

V-FOURS (minimum)

each

55.00

OUTBOARD (Merc) (blind hole)

each

60.00

OUTBOARD (Johnson inline)

each

50.00

OUTBOARD (V-Four)

each

55.00

OUTBOARD (V-Six)

each

60.00

60 Degree (V-Six)

each

65.00

KOHLER, BRIGGS, etc.

each

55.00

HARLEY DAVIDSON

each

50.00

HARLEY Bore & Hone with torque plate

65.00

885 TO 1200 BIG BORE (w/ torque plates)

pair

225.00

OFFSET BORING

add

10.00

BLIND HOLE

add

10.00

TAPER OR CHOKE BORE

add

10.00

010" to .030" (each cylinder)	50.00
.031" to .060" (each cylinder)	60.00
over .060"	add 5.00 each

Add'l cut of .010" to .040"

FOUR CYLINDER

DECK CYLINDER ONLY	45.00
O’RING CYLINDER ONLY	50.00
INSTALL BIG BORE SLEEVES	240.00
INSTALL BIG BORE SLEEVES & DECK CYLINDER	270.00
BIG BORE CASE FOR BIG SLEEVES	75.00

SLEEVING

(Head Studs & Manifolds must be removed)
SLEEVE & BORE STANDARD 2 CYCLE		105.00
SLEEVE WITH HEAVY WALL EXTRA	add	20.00	min
SLEEVE CYLINDER WITH EXHAUST VALVES	add	25.00	min
REMOVE & REPLACE EXHAUST COMPONENTS		20.00	min.
MATCH SLEEVE TO PORTED CYLINDER	add	20.00	min.
BIG BORE SLEEVE	add	20.00
BORE CASE FOR BIG BORE SLEEVE	ea	30.00
SLEEVE FOUR CYCLE (Drop in sleeve)		75.00
SLEEVE FOUR CYCLE (Cast in sleeve)		95.00
SLEEVE OUTBOARD (With ports cut)		195.00
SLEEVE OUTBOARD (With no precut ports)		245.00
SLEEVE KOHLER, BRIGGS, etc.		90.00
REPLATING CYLINDER	ea	220.00
REPLATE & WELD		240.00
Special Sleeves made to your specs, prices will be quoted upon examination.

HONING

HONE NIKASIL	each	12.00
DEGLAZE HONE	each	5.00
RIDGED HONE	each	10.00
RIDGED HONE LARGE KOHLER OR BRIGGS	each	12.00
HONE .001" TO .003" MATERIAL	each	25.00
HONE .003" TO .010" MATERIAL	each	50.00
EXTRA FINE 600 GRIT FINISH	each	5.00
EXTRA FINE 400 GRIT FINISH	each	5.00

CHEMICAL REMOVAL OF ALUMINUM FROM BORE		15.00
*STUD AND MANIFOLD REMOVAL	(each stud) add	2.00
*GASKET REMOVAL PER CYLINDER min.	each	2.00 (min)
* Extra charge for gasket, stud & manifold removal * Rush charge $20.00 minimum per cylinder

REBULDING & TRUE

		2-CYCLE	4-CYCLE
1 CYLINDER CRANK		50.00	50.00
2 CYLINDER CRANK		125.00	125.00
3 CYLINDER CRANK	light wt	175.00	175.00
3 CYLINDER CRANK	heavy wt	200.00	200.00
4 CYLINDER CRANK			250.00
HONDA CR’S WITH FACTORY STUFFER		60.00

CRANKSHAFT TRUING

		2-CYCLE	4-CYCLE
1 CYLINDER		20.00	20.00
2 CYLINDER	min	50.00
2 CYLINDER TRUE & WELD (GOOD CRANK)	min	75.00
3 CYLINDER	min	80.00
3 CYLINDER TRUE & WELD (GOOD CRANK)	min	130.00
4 CYLINDER		125.00	125.00
4 CYLINDER TRUE & WELD (GOOD CRANK)	min	175.00

CRANKSHAFT WELDING

1 CYLINDER		15.00
2 CYLINDER		35.00
3 CYLINDER		45.00
4 CYLINDER		60.00
* Extra charge for making one good crank from two or more bad cranks (minimum) 30.00 * Extra charge for rebuilding previously welded crank (per weld) 10.00 R&R one complete crank journal or more same as complete rebuild * R&R on one crank (end) only (min + true) 30.00

REINDEXING CRANKSHAFT

FOR REINDEXING OF CRANKSHAFT, ADD TO REBUILD CHARGE:

2 CYL/30.00	3 CYL/45.00	4 CYL/50.00
CHECK INDEX	2 CYL/10.00	3 CYL/15.00
REMOVE SPUN OR SEIZED BEARING add 40.00 minimum

PULL CLUTCH

min

10.00

PULL MAG. (FLYWHEEL)

min

10.00

ROD WORK

STRAIGHTEN RODS		ea	10.00
SIZE RODS (per end)	min	ea	12.00
BALANCE RODS (match weight)		ea	15.00
700/800 POLARIS CRANK & CASE UPDATE		ea	175.00

MILL HEAD

1 CYLINDER		25.00
1 CYLINDER (OFFSET OR ANGLED PLUG)	min	40.00
2 CYLINDER SINGLE CASTING	min	50.00
3 CYLINDER SINGLE CASTING	min	60.00
*Add for removal of more than .030"		10.00
SURFACE ANY HEAD .001" OR LESS (per cyl)	each	10.00
MILL CYLINDER BASE (SINGLE)	min	35.00
MILL CYLINDER BASE (TWIN)	min	45.00
MILL CYLINDER BASE (TRIPLE)	min	55.00
DECK CYLINDER (SINGLE)	min	30.00
DECK CYLINDER WITH OFFSET PLUG (TWIN)	min	40.00
DECK CYLINDER SINGLE CASTING (3 & 4 CYL)	min	50.00
*Remove More than .020"	add	10.00
OPEN CHAMBER FOR BIG BORE	each	50.00
RECUT SQUISH BAND	min	35.00
RECUT DOME	each	50.00
WELD AND MACHINE NEW SQUISH BAND	min	65.00
MILL HEAD AND RECUT SQUISH (One Setup)	each cyl	50.00
MILL TWIN & CUT 2 SQUISH (One Setup)		100.00
MILL TWIN & CUT 2 SQUISH (Two Setups)		120.00
MILL 3 CYLINDERS & CUT 3 SQUISH		150.00
POLISH COMBUSTION CHAMBER		15.00
CHECK CC VOLUME (per chamber)	min	15.00
SET cc VOLUME	(per hour)	65.00

ALL PRICES : MINIMUM

STANDARD VALVE JOBS

2 VALVES		50.00
4 VALVES		80.00
5 VALVES		100.00
6 VALVES		110.00
8 VALVES		135.00
16 VALVES		240.00
20 VALVES		300.00
HARLEY DAVIDSON, TRIUMPH, BMW, ETC.	pair	135.00
BRIGGS & KOHLER		40.00

EXTRA CHARGE FOR DISASSEMBLY (ROCKERS/CAMS, ETC)

VALVES

GRIND VALVES ONLY	each	3.50
LIGHTEN AND POLISH		7.50
INSTALL OVERSIZE VALVE	add	15.00
BACK CUT VALVE		4.00
GRIND VALVE SEAT	3 angle	15.00
GRIND VALVE SEAT	1 angle	10.00

GUIDES

SUZUKI GUIDES	add per guide	5.00
REMOVE AND REPLACE	first one	15.00
	add'l (each)	10.00
MODIFY GUIDES FOR OIL SEALS	each	7.00
MAKE OVERSIZE GUIDE	each	35.00
REAM GUIDES TO SIZE	each	2.00

HEAD WORK

MEASURE CHAMBERS cc VOLUME	each	15.00
ADJUST CHAMBER cc VOLUME	per hour	50.00
INSTALL NEW VALVE SEAT	min	65.00

HEAD MILLING (SINGLE CASTING)

1 CYLINDER		40.00
2 CYLINDER		50.00
3 CYLINDER		60.00
4 CYLINDER		65.00
*Over .020" stock removal (addl)	min	10.00

EXTRA CHARGE FOR DISASSEMBLY (ROCKERS/CAMS, ETC)

ALL PRICES : MINIMUM

TWO CYCLE

0 - 100 cc		125.00
125 - 200 cc	min	150.00
250 - 500 cc	min	175.00
PORTING TO CUSTOMER SPECS	minimum	150.00
MATCH MANIFOLD		10.00
POLISH EXHAUST	min	20.00
4-CYCLE	SINGLES TO FOURS	(CALL FOR QUOTE)

LABOR ONLY EACH CYLINDER

PISTONS

DRILL FOR LUBE & COOLING	each	25.00
OIL GROVE	each	15.00
CERAMIC HEAT BARRIER	each	15.00
MOLY COAT	each	15.00
COAT AND HEAT BARRIER	each	25.00
GLASS BEAD AND DECARBON	each	3.50
CUT PISTON SKIRT	each	5.00
CUT BOOST PORT	each	10.00
MATCH PISTON WEIGHTS (MINIMUM)	each	10.00
LIGHTEN AND MATCH	each	15.00
DRILL FOR EXHAUST BRIDGE	each	15.00
RESHAPE CUTAWAY	each	10.00
GAS PORT	each	25.00
CUT OR RESHAPE DOME	each	30.00
RELIEVE FOR EXPANSION	each	15.00
OPEN PIN BOSSES		10.00

ENGINE LABOR/LOWER END

DIRTBIKE/ATV: 2-Cycle

49cc - 125cc		200.00
175cc - 500cc		250.00
without Transmission	min	125.00

ALL 4 CYCLE

min

250.00

SNOWMOBILE & WATERCRAFT

TWINS	min	125.00
TRIPLES	min	150.00

TWO CYCLE TOP END ASSEMBLY

per cyl

40.00

FOUR CYCLE TOP END ASSEMBLY (MINIMUM)

per cyl

85.00

PISTONS COATINGS

MOLY COAT (PISTON SKIRT)	ea	15.00
THERMO BARRIER COAT (PISTON DOME)	ea	15.00
MOLY & THERMO COAT		25.00
COAT USED PISTONS	add	5.00
THERMO COAT CHAMBERS		20.00
THERMO COAT VALVES	ea	10.00

FORK TUBES

STRAIGHTEN FORK TUBE (DISASSEMBLED)	min	each	25.00
STRAIGHTEN FORK TUBE (ASSEMBLED OFF BIKE)	min	each	40.00
STRAIGHTEN FORK TUBE WITH KINK (ADD)	min	each	10.00
STRAIGHTEN TRIPLE TREE AND/OR STEERING STEM			50.00
STRAIGHTEN TOP CLAMP			15.00
STRAIGHTEN AXLE	min		10.00
CHECK FORK TUBE FOR STRAIGHT (ASSEMBLED)			10.00
INSTALL FORK SEALS (ONLY NO TRUING)	min	ea	30.00
INSTALL FORK SEALS WITH TRUING		ea	5.00

LABOR ONLY

		2-CYCLE	4-CYCLE
SPARK PLUG 10 TO 18 mm	HELICOIL	20.00	22.00
SPARK PLUG 10 TO 18 mm	TIMESERT	22.00	25.00
REPAIR WITH HEAD ON	HELICOIL	30.00	35.00
REPAIR WITH HEAD ON	TIMESERT	35.00	40.00

ALL THREAD REPAIR (6-10 mm & 1/4 to 3/8 inch)		first one	15.00
		each thereafter	8.00

HELICOIL INSERTS

6 mm - 10 mm	2.50
12 mm - 18 mm	3.00
1/4 - 3/8	2.50
7/16 - 9/16	3.00

TIMESERTS

6 mm - 10 mm	3.00
12 mm - 18 mm	3.50
1/4 - 3/8	3.00
7/16 - 9/16	3.50

FOR REMOVAL OF BROKEN STUDS SEE (CASE REPAIR)

REMOVE BROKEN STUD (MINIMUM)	each	20.00
REMOVE BROKEN STUD REQUIRING WELDING (MINIMUM)	each	25.00
REMOVE BROKEN STUD W/ BROKEN DRILL BITS, ETC (WELDING EXTRA) MINIMUM	each	30.00
REMOVE AND REPLACE STUDS	each	1.00
REMOVE AND REPLACE HEAD STUDS, CHASE THREADS	each	3.00
REMOVE AND REPLACE CASE STUDS, ADD COST OF NEW STUDS IF NECESSARY	each	3.00
For repair of broken or cracked cases requiring welding or machining, bring in for examination and a quote. Cost of helicoils must be added (See thread repair)

BORE CYLINDER	each	40.00
BORE & HONE CYL WITH TORQUE PLATE	each	45.00
SLEEVE BORE AND FINISH HONE	each	75.00
HONE CYLINDER (rigid hone)	each	6.50
HONE CYLINDER (deglaze)	each	4.00
*STANDARD VALVE JOB	ea. head	40.00
GRIND SEAT ONLY (3 angle)	each	15.00
REFACE VALVE	each	3.00
MODIFY GUIDES FOR OIL SEALS	each	7.00

TIRE & WHEEL BALANCING $15

CARBURETOR BORING (DISASSEMBLED) $45

CARBURETOR BORING (ASSEMBLED)$50

ATC AXEL STRAIGHTENING MINIMUM $45

CLUTCH TRUING (DISASSEMBLED) $40

BALANCE PRIMARY CLUTCH $30

BALANCE SECONDARY CLUTCH $35

TRUE & BALANCE CLUTCH $75

DISASSEMBLE PRIMARY $30

DISASSEMBLY SECONDARY $20

PULL CLUTCH OR MAG MINIMUM $10

CLUTCH REBUILDING MINIMUM $50

RADIATOR REPAIR MINIMUM $20

CHARGE SHOCK $15

GAS TANK REPAIR MINIMUM $25

TRUE DRIVERS 4 WHEELS $30

TRUE DRIVERS 2 WHEELS $25

MACHINE HEAD FOR DUAL PLUGS MINIMUM $40

SURFACE BRAKE ROTOR MINIMUM $40

DRILL ROTOR MINIMUM $75

PROP SHAFT STRAIGHTENING MINIMUM $20

R & R DRIVERS (2) SNOWMOBILE $30

R & R DRIVERS (4) $40

HELI-ARC WELDING

ALUMINUM

MAGNESIUM

STAINLESS STEEL

CHROMOLY STEEL

MILD STEEL

CAST IRON

SILVER SOLDERING

WIRE FEED WELDING

SPRAY WELDING

STICK WELDING

GAS WELDING

BRAZING AND CUTTING

PRODUCTION WELDING

PLASMA CUTTING

MACHINE SHOP SERVICES - $65.00/HR

MILLING - LATHE – DRILLING – BORING – PRESS WORK

BENDING – STRAIGHTENING – METAL SAWING & CUTTING

HIGH PERFORMANCE

ATV PISTONS

FORGED FROM HIGH SILICONE ALUMINUM ALLOY FOR MAXIMUM STRENGTH AND DEPENDABILITY.

DESIGNED TO INCREASE PERFORMANCE AND WITHSTAND THE TREMENDOUS DURESS CREATED BY OFF ROAD CONDITIONS.

No pictures or information may be reproduced without our express written consent